A Gen5 card in a Gen4 slot runs at Gen4. The link trains at the speed both ends support, so the card and its drives get 16 GT/s per lane and about 31.5 GB/s per direction across x16. Nothing on the card can raise that.

That one fact settles the question for a lot of buyers. If your server or workstation has Gen4 slots, the X16 Gen4 and X21 Gen4 give you the full bandwidth that slot can carry, and both are in stock and ready to ship. If you have Gen5 slots, the answer depends on what your workload and your CPU can use. Below are the checks I run, in the order I run them.

Check what the slot actually trains at

The board manual tells you what the slot is meant to do. lspci tells you what it is doing. Find the card's upstream port in lspci -tv, then run:

sudo lspci -vv -s <bus:dev.fn> | grep -E "LnkCap|LnkSta"

LnkCap is what the link can do and LnkSta is what it trained at. 16GT/s is Gen4. 32GT/s is Gen5. Check the width on the same line. A slot that is physically x16 but wired x8 trains any x16 card at x8, which halves the uplink. On the Threadripper board we use for testing, an x16 card trains at x8 in the Gen5 x8 slot and at x4 in the Gen4 x4 slot. StorageReview hit the same thing in its X21 review, where an Intel consumer board connected the card at x8 instead of x16.

The Apex cards are PCIe switch cards, so the slot does not need bifurcation support. The X16 Gen4 and X21 Gen4 use a Microchip Switchtec Gen4 switch, and all the drives sit behind one x16 link as ordinary NVMe devices. Both Gen4 cards are backward compatible with Gen3 platforms and also fit open-ended x8, x4 and x1 slots, at that slot's lower bandwidth. A Gen3 x16 slot carries about 15.8 GB/s per direction.

Check what your network or workload can consume

Data that leaves the box goes over a network link, and the link has a line rate. Divide bits by 8:

Network Line rate Gen4 cards to fill it
25 GbE 3.125 GB/s well under one
100 GbE 12.5 GB/s under one
200 GbE 25 GB/s one
400 GbE 50 GB/s two

The X16 Gen4 and X21 Gen4 both list 30.5 GB/s read and 28.5 GB/s write. 30.5 GB/s is 244 Gb/s, more than a 200 GbE port can carry. If the array feeds clients over 100 GbE, one Gen4 card has about 2.4 times the bandwidth the network can move. A Gen5 card behind the same port does not change what the clients see.

The same arithmetic applies to local work. If your application reads at 10 GB/s, a 30.5 GB/s card already leaves a lot of headroom.

Check what the CPU can drive

Small random I/O can hit a limit inside the host before it runs out of PCIe. In our 2026 lab we ran two X16 Gen5 cards with 32 Gen5 drives in a Xeon workstation (Xeon w7-3445, 20 cores, 40 threads). With the stock interrupt-driven Linux NVMe driver, 4K random reads topped out at about 6.5 million IOPS, and that figure stayed flat from 8 drives to 32. The host's interrupt completion path set the limit. The same host's memory bandwidth also capped sequential reads at 97 to 100 GB/s. Those are Gen5 card results. We have not run that 800-cell campaign on the Gen4 cards, so read them as a measure of the host, not of a Gen4 card.

Now compare a Gen4 card. StorageReview tested the X21 with 21 Samsung 980 Pro 1 TB drives on an AMD Ryzen 9 7950X desktop, 16 cores, under Debian. With fio and io_uring it reported 6.832 million 4K random read IOPS at 28 GB/s, 5.274 million 4K random writes, and 3.454 million 8K random reads at 28.3 GB/s. The card's rated 30.5 GB/s, moved in 4 KiB blocks, works out to about 7.4 million IOPS, so that 4K read result is close to what the card can carry.

The two numbers sit in the same range: 6.5 million on our 20-core Xeon with Gen5 cards, 6.8 million on a 16-core desktop with a Gen4 X21. If your host is in that class and your workload is small-block random I/O, the Gen4 card already delivers about what the host can absorb.

If you are sizing several hosts this way, request a multi-unit quote with the CPU, board and network you plan to use, and we will run these checks with you.

Check power and airflow

Both Gen4 cards draw about 95 W typical when active, through two PCIe 6-pin 12 V connectors. Count those connectors on the power supply before you order, one pair per card.

The product pages list a minimum airflow of 9.86 CFM for the X21 Gen4 and 7.86 CFM for the X16 Gen4. Treat that as a floor and point a fan along the card. In our Gen5 testing on the Xeon workstation, repositioning the chassis fans dropped the hottest drive in the same test from 80 to 51 C. StorageReview put a large external fan on the X21 and saw drive temperatures of 34 to 63 C during a full-write fill. We have not compared Gen4 and Gen5 drives on the cards, so I will not claim a temperature difference between them.

When Gen5 is the right answer

Gen5 earns its place when two things are true. The host has a Gen5 x16 slot that trains at 32GT/s and x16, and the workload needs more than about 30 GB/s from that one slot.

Our best example is sequential read. Two X16 Gen5 cards with 32 drives reached 114 GB/s on a Threadripper workstation (Threadripper 7960X, 24 cores, 48 threads, measured with spec_rstack_overflow=off). That is 57 GB/s per slot, more than a Gen4 x16 link can carry in one direction. Two Gen4 cards in the same two slots would have stopped near 61 GB/s on their spec figures. If you feed 400 GbE from one slot, or your own measurements show a single card holding at the Gen4 link limit, buy the X16 Gen5 or X28 Gen5 and the board to match.

Your host and workload Card
Gen3 or Gen4 slots X16 Gen4 or X21 Gen4
Gen5 slot, network at 200 GbE or below X16 Gen4 or X21 Gen4
Gen5 slot, CPU already caps 4K reads near the Gen4 link limit X16 Gen4 or X21 Gen4
Gen5 x16 slot, workload needs more than about 30 GB/s per slot X16 Gen5 or X28 Gen5
Slot wired x8 or below Fix the slot first

Between the two Gen4 cards, the choice is drive count. The X21 Gen4 holds 21 M.2 drives, 168 TB with 8 TB drives. The X16 Gen4 holds 16, 128 TB with 8 TB drives. Both list the same 30.5 GB/s read figure, so the X21 buys you capacity and drive count per slot, and the X16 needs a little less airflow. Neither needs a special driver. The drives show up as NVMe devices on Linux, Windows and Windows Server, and you pick the RAID: mdadm, ZFS, Storage Spaces or a hardware NVMe RAID card.

Run the lspci check on the host you have today. If LnkCap says 16GT/s, the Gen4 cards are the fit, and they ship now.

Request Multi-Unit Quote · Apex X21 Gen4 product page · Apex X16 Gen4 product page

Related:

  • Which workstation, and which slot, for a 16-drive NVMe card
  • Linux setup checklist for Apex NVMe cards
  • Cooling 16 Gen5 M.2 drives in one PCIe slot